Orbit Mount for Starlink Mini – Assembly and Installation Guide
SpaceTek IT & Communications | Works anywhere you do.
Starlink Mini in-motion magnetic roof mount — step-by-step installation instructions. The SpaceTek IT Orbit Mount for Starlink Mini is designed for vehicle-mounted Starlink connectivity, including use while travelling. This illustrated installation guide explains how to assemble the four-post magnetic mount, position it on a suitable steel vehicle roof and check that all four rubber-coated magnetic feet make full contact. It is relevant to compatible 4WDs, SUVs, utes and work vehicles with an appropriate mounting surface. Read the safety checks before each trip.
What's included in the box

- 1 × white rectangular mounting frame
- 4 × machined aluminium corner posts (A, B, C and D)
- 4 × rubber-coated magnetic feet
- 4 × socket cap-head Allen bolts
- 4 × flat washers
- 1 × matching Allen key
Total: 18 individual components. Each aluminium post is machined for its designated corner and is not interchangeable.

Assembly overview — how the parts fit together
Each corner uses one continuous Allen bolt, washer, aluminium post and magnetic foot. Use this diagram as a reference before following the numbered steps.
Assembling the mount
Step 1 — Prepare the mounting frame

Unpack all components and check them against the list above. Place the frame on a clean, protected work surface. Check all four mounting holes for obstruction and inspect the frame for damage.
Step 2 — Insert the bolts and washers

- Place one flat washer onto each supplied bolt.
- With the frame in its normal upright orientation, as shown in Step 1, insert each bolt down through a mounting hole from the outer face of the frame — the face that will be opposite the Starlink Mini when assembled. The bolt heads and washers remain on this outer face.
- Now flip the whole frame upside down and rest it on a clean, protected bench. In this inverted working position, the bolt heads and washers are underneath the frame, against the bench, and all four threaded bolt ends point upwards towards you, ready for the Starlink Mini and corner posts.
Orientation check: “Top” refers to the frame as pictured in Step 1, before you flip it over. Once it is upside down on your workbench, that same face is underneath. Washers must stay under the bolt heads on that underside; none should be between the Starlink Mini and the corner posts.
Step 3 — Position the Starlink Mini

Carefully place the Starlink Mini face down in the inverted mounting frame. Check that it is correctly seated and aligned with the four bolts. Leave the dish slightly manoeuvrable until all four corner posts are fitted.
Step 4 — Fit the four aluminium corner posts
Use the letters on the aluminium posts to match them to the corners as viewed from the rear of the Starlink Mini in the illustration:
- A: bottom left
- B: bottom right
- C: top left
- D: top right
Position each machined post over its corresponding bolt and seat it around the relevant corner. The posts fit closely to clamp the Starlink Mini. Do not force a post in the wrong corner. Fit all four posts before tightening.
Step 5 — Attach the magnetic feet

- With all four posts seated, screw one rubber-coated magnetic foot onto each exposed threaded bolt through its aluminium post.
- Tighten each magnet firmly by hand.
- If further tension is necessary, use the supplied Allen key on the bolt head from the opposite side of the frame.
Each corner uses one continuous bolt passing through the frame and aluminium post into the magnetic foot. The black rubber contact face must point outwards towards the vehicle.
Step 6 — Inspect the assembly
- All four aluminium posts are fully and correctly seated.
- All four magnets are attached securely.
- The Starlink Mini is held firmly in its frame.
- No components are loose.
- All four rubber-coated magnet faces point towards the vehicle contact surface.
Positioning the mount on a vehicle
Step 7 — Clean and dry the mounting surface
Check the roof material: The magnets require suitable ferrous metal. They will not attach directly to aluminium, plastic, fibreglass or glass. Verify that the chosen roof section is flat and supports full contact at all four magnetic feet.
Choose a suitable ferrous metal surface, then remove dust, dirt, sand and grit and dry it thoroughly. Debris trapped under a rubber-coated magnet can scratch paintwork.
Step 8 — Position for full magnetic contact


Carefully place the assembly on the surface. All four magnets must sit flat and make firm contact. Roof ribs, channels and curved sections can prevent this. Move the assembly to a flatter area, even if off-centre, rather than leaving any magnet suspended over a gap. Pay particular attention to the roof curvature near the windscreen.
Starlink Mini cable connection orientation: Place the mount with the cable connection side of the Starlink Mini facing towards the rear of the vehicle, to help reduce direct exposure of the connector to wind-driven water. The arrow in the reference photograph identifies the vehicle front so it is easier to recognise the opposite, rear-facing connection side. Keep any cable properly secured and clear of pinch points.



Step 9 — Final safety check
Before each trip, inspect all four magnets for full, flat contact, clean rubber coatings, and secure hardware. Stop and recheck the assembly if movement, vibration or a change in position is noticed. When removing it, lift the magnetic feet away individually rather than dragging them across painted surfaces.
- Check every magnet individually for full, flat contact.
- Check that no magnet overlaps a rib, channel or gap.
- Confirm that the mount does not rock or shift.
- Check that all surfaces are clean and every component is securely attached.
Do not use the mount if any magnet is not fully seated or the assembly is insecure.
Important magnetic mount safety information
The Orbit Mount is intended for vehicle-mounted use, including while travelling. Secure installation is essential: retention depends on the vehicle's steel surface, metal thickness, paint, cleanliness, curvature, full contact of all four magnetic feet, and forces from airflow, vibration and movement. Check security before travel and periodically, and stop to inspect the mount if anything changes. The supplier's nominal magnet force is not a vehicle speed rating; do not add four individual magnet ratings together or infer a guaranteed holding force. No specific maximum speed is stated in this guide.
Starlink Mini in-motion mount — frequently asked questions
How do I install a Starlink Mini magnetic roof mount?
Assemble the Orbit Mount using the white frame, four Allen bolts and washers, the four lettered aluminium posts and the four rubber-coated magnetic feet. Follow the photographs in Steps 1–6, then check the vehicle roof and carry out the installation checks in Steps 7–9.
Can I use the Orbit Mount on my 4WD, ute or SUV?
The magnetic feet require a suitable ferrous metal surface that is clean and flat enough for all four feet to sit fully against the roof. Aluminium, fibreglass, plastic and glass panels cannot provide the required magnetic attachment. Check the roof material and contours before installation.
Where should the Starlink Mini magnetic mount sit on a ribbed roof?
Position the magnetic feet on flat metal sections between raised roof ribs and channels. Each of the four magnets must make full contact; never bridge a gap or mount a foot partly over a rib. A slightly off-centre position may work better than a central position on some vehicle roofs.
Which direction should the Starlink Mini cable connection face?
Install the Orbit Mount with the Starlink Mini cable connection side facing towards the rear of the vehicle, as shown in the installation photographs, to help reduce direct exposure to wind-driven water. Secure the power cable so it cannot flap, snag or become pinched.
Is the Orbit Mount designed for Starlink Mini use while travelling?
Yes. The Orbit Mount is designed for vehicle-mounted Starlink Mini connectivity, including in-motion use. Correct mounting and inspection are essential. Check all four magnetic feet, frame fasteners and cable routing before each trip, comply with applicable road rules and Starlink service conditions, and do not assume an unverified maximum speed or magnetic retention rating.
How do I remove a magnetic Starlink Mini mount without scratching the roof?
Lift the magnetic feet away carefully instead of sliding the assembly across the paintwork. Clean the rubber-coated feet and the roof before refitting, and inspect the rubber coating for damage or trapped grit.
Ready to get your Starlink Mini mounted?
Choose a locally made SpaceTek IT Orbit Mount in powder-coated steel or 3mm aluminium. Pick white, textured black or a custom powder-coated colour, and add a cable and DC-DC booster with our optional bundle savings.
Shop the Orbit Mount — View Colours & BundlesNeed assistance?
For help identifying components, assembling the mount or selecting a suitable installation location, contact SpaceTek IT & Communications via our website.
SpaceTek IT & Communications — Works anywhere you do.
